Left View
Headphone speaker line-out amp S PDIF jack Connects to audio line-out devices e.g., speakers, headphones , S PDIF compatible Accepts input from external microphones. Internal optical drive accepts CDs or DVDs. Slot-load optical drive eject button Ejects the optical disk from the drive. Lights up when the optical drive is active.
Disassemble the Cables Antenna and LCD Module
1. Disconnect the touchpad cable and CD-Player cable. 2. Disconnect the wire cable from the board. 6. Remove another two screws located on the each side of the rear side. 7. Then detach the LCD module from the system.
Graphics
ATI MOBILITY RADEON X700 M26P with 128 256 MB of external DDR video RAM supporting Microsoft DirectX 9.0 ATI POWERPLAY 5.0 support PCI Express X16 graphic card support Intel 915GM integrated 3D graphics featuring Intel Graphics Media Accelerator 900 and up to 128MB of VRAM, supporting Microsoft DirectX 9.0 Dual independent display support External resolution refresh rate 1600x1200 120 100 85 75 60 Hz 1280x1024 160 120 100 85 75 60 Hz 1024x768 200 160 120 100 85 75 60 Hz 800x600 200 160 120 100...
External CDROMDVDROM Drive Check
Do the following to isolate the problem to a controller, drive, or CD-ROM DVD-ROM. Make sure that the CD-ROM does not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail. Do the following to select the test device 1. Insert an audio CD into the CD DVD drive. If the CD DVD drive can read the data from the audio CD. The drive does not have problem, then go to next step. If the CD DVD LED on the front panel does not emit light as it read the data...
Disassemble the VGA and Modem board
1. Remove the two screws securing the VGA board. 2. Trun the VGA over and loosen the three screws from the VGA thermal. 3. Separate the VGA thermal from the VGA board. 4. Remove the one screw securing the modem board. 5. Disconnect the modem cable from the position. 6. Detach the modem board from the mainboard.
Hardware Specifications and Configurations
You can install memory modules in any combinations as long as they match the above specifications. NOTE Above table lists some system memory configurations. You may combine DIMMs with various capacities to form other combinations. IC25NG6GATMRG4-G SEAGATE N2 ST96G821A Toshiba Pluto IC25NG6GATMRG4-G SEAGATE N2 ST98G821GA Toshiba Pluto HTS541G1GG9ATGG SEAGATE ST91GG823A Toshiba Aries-B 5X Speed DVD-RAM 8X Speed DVD-R 4X Speed DVD-RW DVD DVD-ROM DVD-5, DVD-9, DVD-10 , DVD-R 3.95G 4.7G , DVD-RAM...
Disassemble the Power Board Bluetooth and Keyboard
1. Insert a scribe into the indent to lift the hinge cover on the right side. 2. Ease the hinge cover up, moving from right to left, and remove it. 3. Remove the screw securing the power board to the system board, and set it aside. 4. Disconnect the bluetooth cable from the routing channels with the tapes following system board. 5. Before you detach the bluetooth, you have to detach the right speaker first. 6. Remove the three screws at the top of the keyboard. 7. Lift up the keyboard and hold...
Disassemble Case Touchpad and CDPlayer
1. Remove the three screws located on the upper case as shown. 2. Remove those five screws located on the upper case as shown. 3. Turn the system over and loosen the five screws from the edge of the system. 4. Remove the seven screws as shown. 5. Disconnect the MIC. cable from here. 6. Tear the tape and disconnect the CD-Player FFC. 7. Remove the two screws securing the touchpad board support. 9. Disconnect the power board cable from the touchpad board. 10. Remove the two screws securing the...
Lid Switch
This section describes the expected behavior of the system when the lid is opened or closed by the user. If the system is running under legacy mode Closing the lid will turn off LCD backlight. If the system is running under ACPI mode The operating system will determine what action to take when the lid is closed. Windows does not define Lid Open action in Power Option control panel The function of lid close will follow the OS setting in power management Nothing, standby, Hibernate or Power off ....
Power Button
The activity of the power button is as follows If power button is pressed for less than 1 second then nothing happens. If power button is pressed for more than 1 second but less than 4 seconds then system would execute User Requested OFF before the system entered into OS. If power button is pressed for more than 4 seconds then the notebook will be powered off by power button over-ride feature. If OS is running in ACPI mode, the power button acts as the sleep button, and let OS controls the...
Wireless LAN Bluetooth Default Setting
After loading default settings in BIOS Follows user setting in previous OS session by ePM or Launch Manager Follows user setting inprevious OS session by ePM or Launch Manager . Controlled by ePM or Launch Manager. Controlled by ePM or Launch Manager.
Insyde Software SCUJul
Main EdEaBEe B Security Boot Exit v Legacy USB Port _Spread Enable IDE Settings Insyde Software SCU Jul 26,2005 11 06 25 Press lt Tab gt key to selectBBI IHHHI H key accept entries. an OKutmll iCancelJ 1 Use cursor, spacebar,
J
ASSY LCD MODULE 17.1 WXGA W GLARE AU B170PW02 V.0 LCD 17.1 WXGA W GLARE AU B170PW02 V.0 2 LAMP GARE TYPE LCD PANEL WITH LOGO W ANTENNA - 10MM
Chapter Sin
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to order FRU parts for repair and...